Do you find yourself interested in info on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably tough project. If the old bathtub is easily available, the project can move easily; if you have to open a wall surface to remove the old tub and position the new bath tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified yourself for the job and fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is far better to think about using one before you start. Possibilities are you may require a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already purchased a brand-new tub and do not need to change the plan of your previous supply of water pipes.
Your devices and also material checklist should make up the following:
Preparing for the Installation
Firstly, the supporting structure supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. When the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bath tub up until the level reviews degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water system as well as check all joints and brand-new pipework for leakages and tighten them if necessary. Fill up the tub and additionally check the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized a minimum of when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to enable the motion experienced when the bathtub remains in usage. The sealant can crack rather early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that editorial about How to Install a Bathtub from an acquaintance on another domain. For those who enjoyed our article kindly remember to pass it around. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Water trouble? Dial.